;
; hello3.step.asm
; step response measurement
; Neil Gershenfeld CBA MIT 10/29/05
;
; definitions
;
.include "tn13def.inc"
.equ chargepin  = PB1 ; charging pin
.equ txpin = PB4 ; serial transmit pin
.def bitcnt = R16 ; bit counter
.def temp = R17	; temporary storage
.def txbyte = R18 ; data byte
.def delaycnt = R19 ; delay counter
.def uplo = R20 ; up low byte
.def uphi = R21 ; up hi byte
;
; start of code
;
.cseg
.org 0
rjmp reset ; jump to reset routine
;
; putchar routine
; assumes no line driver (doesn't invert bits)
;
.equ sb = 1 ;  number of stop bits
putchar:
   ldi bitcnt, 9+sb ; 1+8+sb
   com txbyte ; invert everything
   sec ; set start bit
   putchar0:
      brcc putchar1 ; if carry set
      sbi PORTB, txpin ; send a '0'
      rjmp  putchar2 ; else	
   putchar1:
      cbi PORTB, txpin ; send a '1'
      nop
   putchar2:
      rcall bitdelay ; one bit delay
      rcall  bitdelay
      lsr txbyte ; get next bit
      dec bitcnt ; if not all bits sent
      brne putchar0 ; send next
   ret ; else return
;
; serial bit delay routine
;
.equ b = 17 ; 9600 bps
bitdelay:
   ldi temp, b
   bitloop:
      dec temp
      brne bitloop
   ret
;
; routine to wait for sample to settle
;
.equ delay = 255
settle:
   ldi temp, delay
   settleloop:
      dec temp
      brne settleloop
   ret

;
; main program
;
reset:
   ldi temp, low(RAMEND) ; set stack pointer to top of RAM
   out SPL, temp ;
   ;
   ; init output pins
   ;
   sbi PORTB, txpin ; comm
   sbi DDRB, txpin ; "
   sbi PORTB, chargepin ; charging
   sbi DDRB, chargepin ; "
   ;
   ; init A/D
   ;
   cbi ADMUX, REFS0 ; use Vcc as reference
   cbi ADMUX, ADLAR ; right-adjust result
   sbi ADCSRA, ADEN ; enable A/D
   cbi ADCSRA, ADATE ; disable auto-trigger
   cbi ADCSRA, ADPS2 ; set prescaler for /2
   cbi ADCSRA, ADPS1 ; "
   cbi ADCSRA, ADPS0 ; "
   cbi ADMUX, MUX1 ; input on ADC1
   sbi ADMUX, MUX0 ; "
   


   ;
   ; infinite main loop
   ;
   loop:
     
	rcall settle
	rcall settle
	rcall settle
	rcall settle
	rcall settle
	rcall settle
	rcall settle

         sbi ADCSRA, ADSC ; start conversion
         adloopup:
            sbic ADCSRA, ADSC ; loop until complete
            rjmp adloopup
	 
         in uplo, ADCL ; get low byte
         in uphi, ADCH ; get high byte
        
         mov txbyte, uplo ; low up byte
         rcall putchar
         mov txbyte, uphi ; hi up byte
         rcall putchar
	
      ; send 1 2 3 4 for framing
      ;
      ldi txbyte, 1
      rcall putchar
      ldi txbyte, 2
      rcall putchar
      ldi txbyte, 3
      rcall putchar
      ldi txbyte, 4
      rcall putchar
      rjmp loop