<h3>Surface Mount - 2x3</h3>
<p>Specifications:
<ul><li>Pin count:6</li>
<li>Pin pitch:2.54mm</li>
</ul></p>
<p>Example device(s):
<ul><li>CONN_03x2</li>
</ul></p>
>NAME
>VALUE
<h3>6 Pin Connection</h3>
3x2 pin layout
>NAME
>VALUE
<h3>Multi connection point. Often used as Generic Header-pin footprint for 0.1 inch spaced/style header connections</h3>
<p></p>
<p></p>
<b>You can populate with any combo of single row headers, but if you'd like an exact match, check these:</b>
<ul>
<li><a href="https://www.sparkfun.com/products/12807"> Header - 2x3 (Male, 0.1")</a> (PRT-12807)</li>
<li><a href="https://www.sparkfun.com/products/13010"> Header - 2x3 (Female, 0.1")</a> (PRT-13010)</li>
<li><a href="https://www.sparkfun.com/products/10877"> 2x3 Pin Shrouded Header</a> (PRT-10877)</li>
</ul>
<p></p>
<b>On any of the 0.1 inch spaced packages, you can populate with these:</b>
<ul>
<li><a href="https://www.sparkfun.com/products/116"> Break Away Headers - Straight</a> (PRT-00116)</li>
<li><a href="https://www.sparkfun.com/products/553"> Break Away Male Headers - Right Angle</a> (PRT-00553)</li>
<li><a href="https://www.sparkfun.com/products/115"> Female Headers</a> (PRT-00115)</li>
<li><a href="https://www.sparkfun.com/products/117"> Break Away Headers - Machine Pin</a> (PRT-00117)</li>
<li><a href="https://www.sparkfun.com/products/743"> Break Away Female Headers - Swiss Machine Pin</a> (PRT-00743)</li>
</ul>
<p></p>
<b>Special note: the shrouded connector mates well with our 3x2 ribbon cables:</b>
<ul>
<li><a href="https://www.sparkfun.com/products/10651"> Ribbon Crimp Connector - 6-pin (2x3, Female)</a> (PRT-10651)</li>
<li><a href="https://www.sparkfun.com/products/10646"> Ribbon Cable - 6 wire (15ft)</a> (PRT-10646)</li>
</ul>
>NAME
<b>SOT-223</b>
>NAME
>VALUE
1
>NAME
>VALUE
<b>RESISTOR</b>
>NAME
>VALUE
<b>RESISTOR</b><p>
wave soldering
>NAME
>VALUE
>NAME
>VALUE
<b>CAPACITOR</b>
>NAME
>VALUE
>NAME
>VALUE
<b>CAPACITOR</b>
>NAME
>VALUE
<b>OMRON SWITCH</b>
>NAME
>VALUE
1
2
3
4
(Black)
(Green)
>NAME
>VALUE
>NAME
>VALUE
>NAME
>VALUE
non-polarized capacitor
>NAME
>VALUE
>NAME
>VALUE
<b>Resistor (US Symbol)</b>
<p>
Variants with postfix FAB are widened to allow the routing of internal traces
<b>OMRON SWITCH</b>
>NAME
>VALUE
>NAME
>VALUE
<b>Small Outline IC</b>
>NAME
>VALUE
<b>LLP4x4 body.<p>
http://www.ti.com/sc/docs/package/guide.htm
>VALUE
>NAME
<b>LGA 4x4 DGK. <p>
www.ti.com/audio
>VALUE
>NAME
INDEX AREA
>VALUE
>NAME
The LM4871 is a mono bridged audio power amplifier capable of delivering 3W of continuous average power into
a 3Ω load with less than 10% THD when powered by a 5V power supply (see Note). To conserve power in
portable applications, the LM4871's micropower shutdown mode (IQ = 0.6μA, typ) is activated when VDD is
applied to the SHUTDOWN pin.
Boomer audio power amplifiers are designed specifically to provide high power, high fidelity audio output. They
require few external components and operate on low supply voltages from 2.0V to 5.5V. Since the LM4871 does
not require output coupling capacitors, bootstrap capacitors, or snubber networks, it is ideally suited for lowpower
portable systems that require minimum volume and weight.
<b>Supply Symbols</b><p>
GND, VCC, 0V, +5V, -5V, etc.<p>
Please keep in mind, that these devices are necessary for the
automatic wiring of the supply signals.<p>
The pin name defined in the symbol is identical to the net which is to be wired automatically.<p>
In this library the device names are the same as the pin names of the symbols, therefore the correct signal names appear next to the supply symbols in the schematic.<p>
<author>Created by librarian@cadsoft.de</author>
>VALUE
>VALUE
<b>SUPPLY SYMBOL</b>
<b>SUPPLY SYMBOL</b>
>NAME
>VALUE
PCB EDGE
>NAME
>VALUE
Bluetooth 4.2 BLE Module Shielded Antenna ASCII Interface 9x11.5mm
>NAME
>VALUE
>NAME
>VALUE
<b>RESISTOR</b><p>
chip
>NAME
>VALUE
>NAME
>VALUE
<b>CAPACITOR</b><p>
chip
>NAME
>VALUE
>NAME
>VALUE
<B>DIODE</B><p>
2-lead molded, vertical
>NAME
>VALUE
>NAME
>VALUE
>PRECISION
>PACKAGE
<b>Resistor</b>
Basic schematic elements and footprints for 0603, 1206, and PTH resistors.
Since Version 8.2, EAGLE supports online libraries. The ids
of those online libraries will not be understood (or retained)
with this version.
Since Version 8.3, EAGLE supports URNs for individual library
assets (packages, symbols, and devices). The URNs of those assets
will not be understood (or retained) with this version.